Products

Product : SF600 SPI Flash IC Programmer

SF600 SPI Flash IC Programmer

Description :

The SF600 is a high speed "in System Programming" programmer to update the SPI Flash soldered on board (In Circuit Programming) or in the socket adaptor (Off line programming). The programmer is easily controlled by the computer DediProg Software through the USB bus offering friendly interface and powerful features to users. 
SF600 combines the advantages of SF100 with additional improvements:- High speed USB - Higher SPI performances - Support Single, Dual and Quad IO (ISP mode only).

 

Advanced Features Available

Features :

  • USB High speed and high SPI performance, support up to 1Gb SPI Flash
  • In circuit Programming: Program on board SPI Flash
  • Off line Programming: Program SPI Flash in the socket
  • Support Single, Dual and Quad IO serial communication (new serial Flash protocol)
  • Program two Serial Flash memories
  • Start button feature: Can do Batch function in USB mode
  • Signal conflict protections
  • Multi-Programmers Capability through USB
  • Support 1.8V low voltage IC
  • Support Windows 2003 and above
  • Support both 32 and 64 bit OS

 


The SF600 USB software tool chain offers high flexibility and fit the different and highest requirements:

Engineering Graphic User Interface:
For engineers and expert to access advanced features for development, repairing etc.
Production Graphic User Interface:
For operators in production to control multiple programmers and improve the throughput.
Command line interface:
Customer software can control the multi SF600 programmers (SF600 integration, Control SF600 with Production In Circuit Tester.)


High performance(12MHz, Quad IO):

USB Mode

Memory size

Reference IC W25X80VSIG W25Q16VSIG W25Q32FVSIG W25X64BVFIG W25Q128BFIG W25Q256FVFIG S25FL512SDF01
Density 8Mb 16Mb 32Mb 64Mb 128Mb 256Mb 512Mb
 (Program + Verify) 9s 13s 16s 38s 75s 115s 199.5s

*Please note the programming and verify time will depends on different IC type; please refer to the IC specification before programming.


Hardware :

SF600 is designed with ISP header, through an appropriate connector, users can connect the programmer and drive the SPI signals, supply the memory and control the controller or application status. Please refer to Table 1 for the SF600 2x10 header pin out. DediProg also provides the SF600 ISP Cable which is used to connect the SF600 programmer to the 2X6 2.54mm ISP Pin Header on board, please refer to Table 2 for the SF600 ISP Cable 2x6 pin out.

Table 1: SF600 ISP Header Pin Out (2x10)
1 Vpp CS2 2
3 CS1 Vcc 4
5 MISO/DQ1 Hold/DQ3 6
7 Wp/DQ2 CLK 8
9 GND MOSI/DQ0 10
11 NC Reset/IO3 12
13 NC NC 14
15 NC NC 16
17 NC NC 18
19 GPIO1 GPIO2 20
Table 2: ISP Cable Connector Pin Out (2x6)
1 Vpp CS2 2
3 CS1 Vcc 4
5 MISO/DQ1 Hold/DQ3 6
7 Wp/DQ2 CLK 8
9 GND MOSI/DQ0 10
11 NC Reset 12

Contents :

  • 1 x SF600 Programmer
  • 1 x USB Cable
  • 1 x ISP Cable (ISP-600-CB1-G)
  • 1 x SF100 2.54mm 2*4 ISP Cable (ISP1-CB)
  • 1 x SF600 Universal Adaptor (ADP-SF600-TO-SF100)
  • 1 x CD-ROM (Included Software, specifications and user manual)

Hardware Requirement for ISP :

To have a clear understanding on the different ISP or backup boot methods and different reference schematics, please download our dedicated application notes: AN0103 and AN0106 in the documentation section.


Option Purchase :

  • Backup Boot Flash-SO8N
  • Backup Boot Flash-Dual SO8N
  • Backup Boot Flash-SO8W
  • Backup Boot Flash-Dual SO8W
 
  • Backup Boot Flash-SO16W
  • Backup Boot Flash-Dual SO16W
  • BBF SO8 Testclip
  • BBF SO8 Testclip-Dual
 
  • BBF SO16W Testclip
  • ISP SO8 Testclip
  • ISP SO16W Testclip
  • SF100 Universal Adaptor 

Downloads

Click here to Download Broucher

 
Back to Top