Products

Product : SF100

SF100

Description :

The SF100 is a high speed "In System Programming" programmer to update the SPI Flash soldered on board or Freescale MCU using Ezport. The programmer is easily controlled by the computer DediProg Software through the USB bus offering friendly interface and powerful features to users.

 

Advanced Features Available

  • Features :

    • USB Interface
    • Start button feature
    • Signal conflict protections
    • Update Serial Flash soldered on board with application powered or not
    • Control Application, controller reset and MOSFET isolation status
    • Update the internal Flash of Freescale MCU using the Ezport (MCF5223,MCF5221,MCF5213) or the external SPI Flash of Freescale MCU using the SBF interface (MCF5445, MCF5227)
    • Capable of handling two serial flash memories (new feature; provided in SF100 with serial number DP001325, firmware 2.0.4, software 2.0.37 and after)
    • Multi-Programmers Capability
    • Support Windows 2003 and above
    • Support both 32 bit or 64 bit OS
     

    The SF100 USB software tool chain offers high flexibility and fit the different and highest requirements:

    Engineering Graphic User Interface:
    For engineers and expert to access advanced features for development, repairing etc.
    Production Graphic User Interface:
    For operators in production to control multiple programmers and improve the throughput.
    Command line interface:
    Customer software can control the multi SF100 programmers (SF100 integration, Control SF100 with Production In Circuit Tester..)


    High performance:

    USB Mode

    Memory size

    Reference IC W25X80VSSIG W25Q16VSSIG W25Q32FVSSIG W25Q64CVSSIG W25Q128BVFIG W25Q256FVFG S25FL512SAIF01
    Density 8Mb 16Mb 32Mb 64Mb 128Mb 256Mb 512Mb
     (Program + Verify) 11s 15s 20.5s 48.5s 94s 157s 297s

    *Please note the programming and verify time will depends on different IC type; please refer to the IC specification before programming.


    Hardware :

    SF100 is designed with ISP header, through an appropriate connector; users can connect the programmer and drive the SPI signals, supply the memory and control the controller or application status. Please refer to Table 1 for the SF100 2x7 header pin out. DediProg also provides the SF100 ISP Cable which is used to connect the SF100 programmer to the 2X4 2.54mm ISP Pin Header on board, please refer to Table 2 for the SF100 ISP Cable 2x4 pin out.

    Table 1: SF100 ISP Header Pin Out (2x7)
    1 I/O1 I/O4 2
    3 I/O2 or CS2 NC 4
    5 Vcc GND 6
    7 CS CLK 8
    9 MISO MOSI 10
    11 Vpp/Acc I/O3 12
    13 SCL SDA 14
    Table 2: ISP Cable Connector Pin Out (2x4)
    1 Vcc GND 2
    3 CS CLK 4
    5 MISO MOSI 6
    7 Vpp/Acc I/O3 8

    Contents :

    • SF100 Programmer*1
    • USB cable*1
    • ISP cable*1
    • SF100 Universal Adaptor*1
    • CD-ROM*1(Included Software, specifications and user manual)

    Hardware Requirement for ISP :

    To have a clear understanding on the different ISP or backup boot methods and different reference schematics, please download our dedicated application notes: AN0103 and AN0106 in the documentation section 


    Option Purchase :

    • Backup Boot Flash-SO8N
    • Backup Boot Flash-Dual SO8N
    • Backup Boot Flash-SO8W
    • Backup Boot Flash-Dual SO8W
     
    • Backup Boot Flash-SO16W
    • Backup Boot Flash-Dual SO16W
    • BBF SO8 Testclip
    • BBF SO8 Testclip-Dual
     
    • BBF SO16W Testclip
    • ISP SO8 Testclip
    • ISP SO16W Testclip
    • SF100 Universal Adaptor 

     

Downloads

Click here to Download Broucher

 
Back to Top